T-600 Series Transfer Station Compactors


The T-600 series is designed for medium sized solid waste transfer stations for both the private and municipal sectors. The clear top opening provides adequate space for loading via front-end loader or conveyor. The base shell can be upgraded to include AR-450 wear plates (floor and side walls) as well as tongue and groove floors that reduce waste debris from migrating under the ram between the shell floor and the ram floor. The base shell can also be fitted with a “scoop” ram face that results in improved trailer payloads and pack-out time with less spillage when the trailer is removed. An oil cooler, oil heater, and pre-press can be added to the base unit; and the client can choose from manual or hydraulic side mounted trailer clamps or an hydraulically operated center clamp. Each system can be further customized to suite the client’s needs and can be supplied as part of a 100% turnkey system.

Learn MoreBook a consultation

Technical Details

Standard Features

  • UL/CSA Approved Design
  • Meets/exceeds ANSI Z245.2 regulations
  • Meets/exceeds OSHA regulations
  • PLC “flex-design” based control systems
  • NEMA 4 rated enclosure
  • Internal timers prevent system run-on
  • Self-diagnostic indicators
  • 24-volt controls
  • Adjustable multi-cycle timer
  • 75% and 100% full light
  • Auto-alert maintenance mode
  • Heavy duty oil-tight pushbutton controls
  • Key lockable start pushbutton

Mechanical Specifications

Charge Chamber Volume6.
Charge Chamber Opening Size96″ x 78″96″ x 78″96″ x 78″96″ x 78″
Ram Face Size36″ x 60″36″ x 60″36″ x 60″36″ x 60″
Ram Penetration24″24″24″24″
Compaction Force Normal56,500 lbs76,930 lbs113,000 lbs63,585 lbs
Compaction Force Maximum62,172 lbs88,470 lbs124,344 lbs69,945 lbs
Cycle Time63 seconds73 seconds63 seconds63 seconds
System Pressure Normal2000 psi2000 psi2000 psi2000 psi
System Pressure Maximum2200 psi2200 psi2200 psi2200 psi
Pump Capacity20 gpm25 gpm30 gpm20 gpm
Motor Size30 hp30 hp40 hp30 hp
Cylinder Size1 x 6″ dia.1 x 7″ dia.2 x 6″ dia.2 x 5″ dia.
Cylinder TypeDouble ActingDouble ActingDouble ActingDouble Acting
Ram Face Pressure Normal20.1 psi27.4 psi40.2 psi22.6 psi
Ram Face Pressure Maximum22.1 psi31.5 psi44.3 psi24.9 psi
Oil Tank Capacity75 gal75 gal200 gal75 gal
Shipping Weight (Head only)11,850 lbs13,050 lbs15,950 lbs11,850 lbs

Electrical Specifications

Control System110 volt 60 cycle powered by step-down transformer
Control PanelFully wired. Keyed start button, emergency stop, full lights, reset button, PLC, current sensor
Power208/230/575 Volt, 3 Phase 60 Cycle


Table Diagram


Electrical system upgrades

  • System monitor: SCADA panel (add-on panel or integrated upgrade) provides cell-based monitoring of all systems including container fullness, safety circuit devices, container positioning, hydraulic system devices including reservoir fullness, oil temperature and system in-use time
  • Remote start/stop station
  • Auto-start system (photo-eye or sonic sensor)
  • Wireless remote control
  • Biometric interface
  • HMI based operator interface for tie into building monitoring systems

Hydraulic system upgrades

  • Single phase and three phase power units
  • Hi-lo hydraulic pumps for reduced cycle time applications
  • Regen circuit for improved hydraulic fluid circulation
  • Over-sized oil reservoirs to accommodate ancillary devices and improved heat sink
  • Oil cooler for high duty cycle applications
  • Bio-degradable oil
  • In tank oil heater
  • Sonic sensors for oil fullness monitoring
  • Low temperature oil (as low as -60 Celsius is available)
  • Custom chute systems
  • Custom weather enclosures
  • Drive-on deck systems (certified up to 20,000 lbs.)
  • Tongue and grooved floor designs
  • AR plate floors and sides for reduced press head/compactor shell wear
  • Pad-less set-up for installation on asphalt
  • Custom hydraulic cart tipping systems
  • Light curtain-based safety sensors
  • Custom steel safety barriers
  • Custom hydraulic lift systems
Download documentation